Art Level — Hang it true.

Captured wall used for arranging artwork

Gyro auto-level

Set eye level firstConfirm the 58-inch eye-level line before using it as the laser datum.

equal spacing

Hold phone square to wall · 0°

Square up the frame0.0°

Move until the edge border turns greenRed is badly angled, yellow is close, and green is square to the surface.

Quick start

Snap a photo of your art or frame.
Size is estimated automatically. Tap any placed frame to adjust its width and height.

Allow camera and motion access when prompted.

Eye-level heightin Wall distancein

Add artwork

Photograph or choose your art, then place it on the live wall view.

Check the frame dimensions

Width (in)

Height (in)

Weight (lb) — optional

Which dimensions did you enter?Use the OUTER frame edges, including the mat and molding. Print or glass size makes the wall preview too small.

Confirm outer frame dimensions to continue.

Flip the frame, snap the back.The photo stays in the project file. On-device checks suggest the mounting system; you confirm it before placement.

Looks like a wire, right?Best match from on-device image checks — confirm or correct below.

Mounting system

Unloaded wire drop from top (in)

Left D-ring drop (in)

Right D-ring drop (in)

Point spacing (in)

Wire slack under tension2.5 in

Frame weight range

Pro · enter exact weight

Exact frame weight (lb)

Wall type

Wall fastener

Add frame hardware

Wall distance

Set the measured distance from the phone camera to the wall for accurate scale.

Phone to wall (inches)

Pro calibration
Fine-tune the crosshair, switch leveling modes, or map studs from two blue tape marks.

Vertical line offset (in)

Horizontal line offset (in)

Stud map from blue tape
Put blue painter’s tape over two known studs, then aim the camera at both marks.

Stud spacing

Measured tape distance (in)

No stud references detected yet. Drill points turn green on a stud; orange means use a rated drywall anchor.

Laser detection looks for bright red or green cross-lines in the live camera. For best scale, keep the phone aimed square to the wall.

Eye-level line

Set the real height of the gyro-leveled horizontal line above the floor.

Datum height (inches)

Visual-match adjustmentIntentionally tilt the datum to match a sloping mantel, sagging ceiling, or unlevel furniture. This is not mathematical level.

0°

Frames & projects

Review this layout, keep a named copy during this session, or open and download a project file.

Project name

No session projects yet.

Open file

Wall reference

Mark a door or window edge, desk top, or existing art. Set a clearance, then snap the selected frame to its guide.

Select a frame to see its live edge distance.

Label

Edge direction

Custom label

Target clearance (inches)

Frame size

Adjust the width and height for this placed frame.

Width (in)

Height (in)

Weight (lb) — optional

Wall grids

Choose guides to overlay on the live wall view. The eye-level datum stays separate.

1-inch gridScaled from wall distance and the camera field of view.

Snap to gridSnap a dragged frame’s center or nearest edge to the 1-inch grid.

Stud linesShow equally spaced vertical stud guides.

20 in

CenterlinesShow the wall’s horizontal and vertical center.

Rule of thirdsShow a three-by-three composition guide.

Project store

Start with this job’s exact hardware bundle, or filter trade-ready kits by installation scenario.

One-Tap Project BundlerExact hardware from this project’s drill sheet.0 frames

Configure a frame’s weight and wall type to build this bundle.

Trade-ready kits

Prices are dated snapshots and may change on Amazon. As an Amazon Associate I earn from qualifying purchases.

Drill sheet

One trusted hole list drives the wall overlay, scaled drill map, tape-measure steps, and installer packet.

Pro drill mapLeft edge + floor datum

No holes

Add and configure a frame to build the drill sequence.

Drill points0 points

Hardware to bring

Capture the wall

Make one still wall view for planning. Keep a single 2-inch blue painter’s-tape square visible; it becomes the shared scale and alignment reference.

1Capture

2Arrange

3Hang

Before the shotFace the wall squarely, include the whole layout area, and measure camera-to-wall distance. Keep the tape in place until hanging is complete.

Use the live rear camera or upload a wall photo.
After the image appears, tap the center of the blue tape if it was not found automatically.

Straightened

No wall image yet.

Camera to wall (in)

Horizontal camera view (°)

On laptop: drag frames, scroll to zoom the wall, arrow keys nudge ⅛ inch (Shift = 1 inch), and right-click a frame for options.

Physical laser match

Aim at a horizontal green laser beam. Pro detects the high-saturation green line, places the digital datum over it, and follows it while the beam stays visible.

Not calibratedStart the wall camera, then scan the beam.

Nudge the lockIf the digital line sits just above or below the beam, move it in ⅛-inch steps without losing tracking.

0 in

When locked, every Pro drill point shows its horizontal distance from the left reference and its signed offset above or below the physical beam.

Share project

Share one .artlevel job packet with the wall plan, drill coordinates, and auto-generated hardware shopping list. The recipient can open it in Art Level Pro.

Keep a visual copyBefore you leave the finished wall view, take a screen capture for a quick visual reference.

Unlock installation tools

Pro adds the field-ready tools for taking a finished wall plan through drilling and hardware setup.

Mounting-system setup and hardware recommendations
Physical laser calibration, stud guides, and drill coordinates
Pro drill map, job packet, and project-file upload

$29.99 onceEARLY10 takes $29 off
10 early-adopter spots

Go Pro — $0.99 with EARLY10

After checkout, use Launch Pro on the confirmation page. Pro stays unlocked for that app session.

Add artwork

Add frame hardware

Wall distance

Eye-level line

Frames & projects

Wall reference

Frame size

Wall grids

Menu

Wall workflow

Connection

Art Level Pro

App

Settings

Project store

Trade-ready kits

Drill sheet

Hardware to bring

Capture the wall

Physical laser match

Share project

Unlock installation tools